It looks like you're new here. If you want to get involved, click one of these buttons!
Subscribe to our Patreon, and get image uploads with no ads on the site!
Base theme by DesignModo & ported to Powered by Vanilla by Chris Ireland, modified by the "theFB" team.
Comments
I'm using the GS Mini for shape and size of body as I randomly picked up a mold for one a couple of years back
Instagram
I also have a 15' radius dish for the back arch.
A matching top could be something I liked, but mainly the thought arrived because I have 2 identical sets of wood
Instagram
First they were Thicknessed to 2mm. I did this by putting them on a backing board and sending through the thicknesser. This is very risky and only works here because its straight grained walnut and cuts well. you can quickly destroy a set of sides trying this with anything figured or more brittle. They will now be scraped down to about 1.8mm. Walnut usually bends really well so, very forgiving at these kind of dimensions.
The back and top will need to be hand planed and scraped to thickness. The thicknesser is too risky for those, and I don't have the luxury of a thickness sander yet
After that I marked them up and cut the rough taper. usually I bend at full width and add the taper after, but i'm trying it the other way round here.
Instagram
Instagram
Instagram
Watching with interest, @WezV
The sides have been trimmed to length and i made neck and tail blocks out of some random chunks of mahogany type wood - most likely Sapelle.
I still haven't decided if it will be mortice and tenon, or a dovetail join... so i've gone for a traditional block that will allow either
Instagram
I am traveling at the moment so don't have much to hand but with the shorter body at 17" ISTR and the longer neck where does that move the bridge to?
Anyway, its a format I love for smaller acoustics if you are not looking for a conventional acoustic tone then you can get a nice voice out of solidi Walnut back and front.
As always will be following along with much interest
Think of it like a baritone tele with Floyd and humbuckers. We still call it a tele based on body shape, even though by that point it sounds nothing like one
The drawing in the first post shows where the bridge ends up with a 14th fret body join and 24.75" scale. The saddle will be 13.9mm further back due to the extra 31.75mm of scale length.
It's going to push the bridge closer to the center of the lower bout, which should increase responsiveness. If it works, it will get more tone and volume out of the smaller size. If it doesn't, it will likely get a bit muddy when strummed
Instagram
I only had 3mm perspex here, so laminated 2 bits together and you can see some of the glue between layers. Mounted the dremel router base, and drilled some pin holes at set distances. I think i will enlarge the main hole in the base to prevent it getting clogged.
I just need to be aware of bit size with this, but can drill more pin holes if needed. The 40-50mm holes are for soundholes, 55-65 for rosette.
Instagram
I now have soundhole cut and two channels for a basic rosette made from offcuts of the back wood and a little black veneer. That will get glued in place, and should look pretty clean once scraped back.
Instagram
Instagram
I glued the back on yesterday, top soon. Will get pics at some point.
I also started on the neck. My uncle dropped round some reclaimed mahogany recently that he nearly just burned in his fire.
At the front of the pile was this piece, covered in varnish and no more nails, but a very promising tap tone.
It was only 40mm thick, and had quite a bit of damage down one end from when it was reclaimed with force.. but looks like enough for a 2 piece neck. Not quartersawn, but the grain is nicely mirrored so should work well.
After that I put it through the planer and took away all the damaged edges
It's some really nice wood. But I did discover one flaw when planing. There is a small hole that could have written this off.
But thankfully it is pretty much spot on the final depth of the neck, and only goes half way through that laminate, it should be easily removed in the carve.
The extra tabs will allow me to add some pins when gluing it together. I include them when cutting the laminates individually like this, not so necessary if gluing the block before cutting
Instagram
I got a nice surprise when the plane hit it. I suspected there was a little figure from the sides. But not this consistently flamed.. I got lucky with the chevron pattern.
Body is glued together and ready for trimming back
Instagram
Instagram