I've taken a few photos as I've gone along (though not really any "before" shots), so thought I'd do a build thread of sorts.
Basically, our house has an extremely steep back garden which the previous owners had built tiered decking on. Unfortunately due to some design flaws it hadn't lasted well, it was in a bad state of repair, and some of it was frankly dangerous.
As well as that, a large part of the garden was very overgrown with 20' laurel hedging, and other overgrown trees, and was really too steep to do anything with.
I came to the realisation that when the time came to sell the house, I'd really need to at least replace the decking, so figured I may as well do it now and enjoy it for the next few years too.
Initially I had wanted to get a landscape gardener to do it, but the quotes we got were in the £15-20k+ region, so I decided to do it myself, and saved ~£15k in the process
I should add a couple of caveats for anyone considering doing something similar: firstly, the decking I put in was replacing an existing structure so planning wasn't an issue (and i get on well with our neighbours and made sure they didn't mind out of courtesy before starting anything). Secondly, my father in law worked as a builder/tradesman and built their house from the ground up so I had access to expert advice if I got stuck (as well as having access to a good chop saw which made life a lot easier).
I started the project in May, and have been doing it in evenings and weekends on and off since then as time allows.
Robot Lords of Tokyo, SMILE TASTE KITTENS!
Comments
https://i.imgur.com/OJxLSpq.jpg
The trunk at the front of the pic is what was left of one of the laurels, there were about 6 large trailer loads of it removed (the pile below is about 20% of it)
https://i.imgur.com/uxvGPPa.jpg
And a view from the bottom showing how much old rotten decking there was to be removed and the overgrown trees at the back left
https://i.imgur.com/EKJhccy.jpg
https://i.imgur.com/Yxw8lHm.jpg
Which after a couple more trips ended up looking like this:
https://i.imgur.com/mTgZWRS.jpg
https://i.imgur.com/XdSND07.jpg
https://i.imgur.com/Qaw7lqV.jpg
https://i.imgur.com/xpQaW5g.jpg
https://i.imgur.com/0SmSlMv.jpg
Then there was a couple of weeks break with work and then holidays
It was a steep slope, and I'd always thought a BBQ area with paving would be nice.
First I had to build a retaining section to build up the ground level (it's about 3 1/2 feet built up):
https://i.imgur.com/nzrzZXy.jpg
Then excavate out the hill by hand:
https://i.imgur.com/YMxpWBl.jpg
https://i.imgur.com/y48JmuN.jpg
I've used a mortarless retaining block system for the retaining walls, which has the advantage of being very easy and quick to put up, and the disadvantage of being more expensive than a conventional bricks/mortar wall:
https://i.imgur.com/UWsEgmX.jpg
https://i.imgur.com/XvPBURO.jpg
the soil was in direct contact with the timbers and made them rot. To solve this I've put posts in concrete with boards along them to keep the soil back. This also serves to ensure the edge of the paving will be pretty near level with the edge of the decking.
https://i.imgur.com/VkYnPvn.jpg
The slabs are stone of some sort (they're napped rather than cut), they're sold as black limestone although I'm not sure I believe that.
Here's one unfinished:
https://i.imgur.com/Jn7p9mS.jpg
I had to resist the temptation to put them down in perfectly even rows, and forced myself to do something more artistic.
Here they are after a hard morning's work, with the first couple of rows of retaining blocks down:
https://i.imgur.com/WAzbP3a.jpg
And here it is with some sealant on it, which is pretty much the colour they are now:
https://i.imgur.com/eAAIDkx.jpg
Firstly supporting the ground to prevent any slippage:
https://i.imgur.com/3qGjpYL.jpg
Followed by building up a few rows of the blocks:
https://i.imgur.com/0B8L3XI.jpg
The beauty of these is that you can do curves in them very easily, and they also split fairly cleanly with a bolster and heavy hammer for doing even ends:
https://i.imgur.com/DHv6Xeh.jpg
I tore up the old decking and removed any joists that were rotten. The area at the very top is sheltered under some trees so doesn't really get wet, so the stair stringers were in surprisingly good condition, so they were kept.
As you can see, I'm using a damp course between the joists and the boards to prevent rot being such a problem. It's designed in such a way that the water tends to run off and the joists stay dry.
https://i.imgur.com/m570Cj1.jpg
And after getting the boards down:
https://i.imgur.com/EVW0rTa.jpg
I'm using 4' eased edge posts for the handrail supports, attached with 100mm timber screws which despite holding very strongly are self drilling and don't split the wood.
I special ordered the joists. Standard ones are 2"x6" and would be roughly comparable to C16 timber although they're not as finely sawn/finished. I wanted something stronger as about 1.8m of the decking in one corner is cantilevered, so was able to get 2"x8" C24 graded timber that had been pressure treated. This took a couple of weeks to get hold of, but was definitely worth it.
Here's the joists (before I fully braced them) with some boards just sitting on top to work out spacing and squareness:
https://i.imgur.com/1NXGbpJ.jpg
https://i.imgur.com/p2k1e0j.jpg
https://i.imgur.com/NAV1toN.jpg
https://i.imgur.com/adZfeoD.jpg
https://i.imgur.com/xbL0DzP.jpg
https://i.imgur.com/zVPKBd0.jpg
https://i.imgur.com/Y9ERi63.jpg
That's a pond liner!
I'd always wondered why that bed had been so damp, it looks like the previous owner had a pond and then filled it in at some stage with soil without ever removing the liner.
Needless to say I cut out a large portion of the liner and the drainage is much better now.
You've made me feel inspired to get my patio finished
https://i.imgur.com/b8nELsl.jpg
I'm using 400mm centre to centre spacing on all of this BTW
Next the boards:
https://i.imgur.com/71Zy1pl.jpg
And finally making steps to get between levels.
For these short runs I'm using 2x10 pressure treated boards. This gives much higher strength than the other options which are basically using 8x10 and having much narrower support sections, or nailing angled risers onto a beam, which in my experience doesn't hold well in the long term.
For every cut, I treat the end grain with preserver (although you can see that the tanalising process has let it soak right through to the centre).
I used the mitre feature on the chop saw to get even cuts, and finished some of the longer cuts with a hand saw.
https://i.imgur.com/zFn5fId.jpg
And with the stairs in place;
https://i.imgur.com/zszOJmq.jpg
While I was waiting for the deliveries, I thought about what to do with the left hand side of the garden.
It was steep, but needed to be accessible and low maintenance.
In the end I put in pebbles under mesh to retain them on the slope, and cut in some steps which were then faced with left over joist timber.
Eventually I made some more progress on the decking (also showing a couple of the steps and the pebbles under wire:
https://i.imgur.com/tIhwVG4.jpg
The next job was the short stair section between the deck levels.
You can see they run off in different directions, so had to build the stairs to run from a tilt to the right at the bottom to a tilt to the left at the top.
https://i.imgur.com/jjycbzr.jpg
Which worked pretty well in the end:
https://i.imgur.com/A7XKZnC.jpg
https://i.imgur.com/YzTDeWn.jpg
https://i.imgur.com/SFhh4ka.jpg
https://i.imgur.com/Bhcoued.jpg
https://i.imgur.com/OHbFWf1.jpg
Which again due to the speedy nature of these mortarless blocks only took an afternoon.